Option Board SDI I/O v2
Option Board SDI I/O (O_DAP_SDI_b)
Standards
- Video complies with SMPTE 424/425M (3G, Level A and B), SMPTE 292M (HD), or SMPTE 259M (SD)
- Automatic format detection
- Audio embedding and de-embedding complies with SMPTE 299M (3G, HD) or SMPTE 272M -AC (SD)
- Metadata embedding and de-embedding complies with SMPTE 2020-2
Video Data Rate
- 2970/296Mbps (3G), 1485/1483.5Mbps (HD), 270Mbps (SD
Video Formats
- 1080p - 23.975, 24, 25, 29.97, 30, 50, 59.94, 60
- 1080i - 50, 59.94, 60
- 720p - 23.975, 24, 25, 29.97, 30, 50, 59.94, 60
- 625i - 50
- 525i - 59.94
Video Delay
- User selectable 0 ... 50 frames, can be disabled
Audio
- 24-bit, transparent forwarding of PCM and compressed audio
- Sample rate = 48kHz (SDI compliant)
- Channels = 16 inputs and 16 outputs (4 groups of 4 channels each)
- Delay = Embedder audio delay selectable 0 ... 320ms per channel
Metadata (RDD6)
- 1 channel input, 1 channel output, SDID selectable
BNC Input
- Impedance = 75Ohm
- Return loss = >15dB 5 ... 1485MHz; >10dB 1485 ... 2970MHz
- Maximum cable length = 250m (SD), 230m (HD), 140m (3G) using Belden 1694A cable
- Jitter tolerance = >0.7UI (alignment)
BNC Output
- Impedance = 75Ohm
- Output voltage = 0.8Vpp (typical)
- Return loss = >15dB 5 ... 1485MHz; >10dB 1485 - 2970MHz
- Output jitter = <0.2UI (alignment), <0.5UI (timing)
Latency
- Video latency input to output = 120 ... 200 pixel, depending on video standard
- Audio latency input to output, embedder and de-embedder combined = <0.6ms (HD, 3G), <2ms (SD)
General Features
- Power fail relay bypass (may be enabled/disabled via GUI)
- Lip-sync compensation for processed and non-processed audio signals
- Dedicated routing for non-processed channels; all channels (maximum 16) can be routed to/from the device or looped through
- Test pattern generator (no genlock)
- Master-sync capable
- ITU-R BT.1685 / ARIB STD-B39 metadata support
SDI Card Self-Test
The SDI card provides a built-in self-test for verifying the SDI signal path in all three supported physical signal formats: SD, HD, and 3G.
The exact video resolution or frame rate is not important for this test. One valid signal format from each of the three categories is sufficient.
Test Setup
- Connect the SDI output back to the SDI input using a suitable cable to create a loop-through connection.
- Enable the SDI generator.
- Set the generator output to Black.
- Enable Delay.
Running the Test
Perform the test once for each of the following signal formats:
- SD
- HD
- 3G
For each format:
- Select any valid video format within the required SDI category.
- Wait while the self-test runs.
- Observe the status LED.
- Wait until the test has completed successfully before changing to the next signal format.
Each individual test takes approximately 30 seconds.
Note - The exact video resolution or frame rate does not matter. The self-test only requires one successful test in each physical SDI format: SD, HD, and 3G.
If a test does not complete successfully, it is automatically restarted and continues to run until the test passes.
LED Indication
| LED Status | Meaning |
|---|---|
| Fast flashing blue | A self-test is currently running. |
| Slow flashing blue | The self-test sequence is incomplete. At least one of the SD, HD, or 3G tests has not yet been completed successfully. |
| Solid blue | All three tests — SD, HD, and 3G — have completed successfully. |
Important - Do not proceed to the next signal format until the current test has completed successfully and the LED indication has stabilized.